Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
The publisher is making a number of good points about Tools You Need to Install a New Bathtub as a whole in this post down below.
Setting up a tub isn't specifically brain surgery, however it does require solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is readily available, the task can move immediately; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. Make certain you have actually certified on your own for the work and also fit attempting it. As opposed to working with a specialist to take over a halfway-completed job, it is far better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you set up a brand-new tub in your bathroom if you have actually already acquired a brand-new tub as well as do not need to alter the arrangement of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installment
To start with, the supporting structure supplied with the bathroom should be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic because of the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to going on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the required setting. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next objective is to make sure that the tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub up until the spirit level reviews degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system and inspect all joints and new pipework for leaks as well as tighten them if necessary. Load the bath tub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Finally, fix the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has been utilized a minimum of once as this will settle it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. Once the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous kind should be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, leading to complications with dampness as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealer can crack rather very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that editorial on How to Install a Bathtub through a friend on our other website. For those who enjoyed reading our blog entry kindly do not forget to pass it around. Many thanks for going through it.
Top service, one call. Report this page